Effect of sintering temperature on lightweight aggregates manufacturing from copper contaminated soil

Manufacturing lightweight aggregate (LWA) at high temperature is an effective way to immobilize heavy metals in solid waste. This work investigated the performance and solidification mechanism of LWA prepared from copper contaminated soil. The volume expansion of LWA could reach a maximum of 28%, and its lowest density accounted of 1.5 g/cm³, which met the standard requirements. Optical microscope and micro-CT test illustrated that the addition of Cu leaded to obvious phase separation in LWA. The Cu leaching result of LWA first increased and then dropped with the temperature. The XRD test found that the main formation phase of Cu in LWA were t-CuFe₂O₄ and amorphous phase that they had different acid resistance ability. XPS revealed that the main cause of the agglomeration of liquid phase in LWA was the chain broken reaction between Cu and Si–O tetrahedron. SEM-EDS results showed that the distribution of Cu and Si had a strong correlation, which meant that Cu mostly formed amorphous phase. This work showed the uniqueness of Cu in the high temperature immobilization and pointed out the best immobilization target phase.     

脱硫胶粉在乳化改性沥青中的应用

考察了不同规格胶粉及不同脱硫程度的脱硫胶粉对橡胶改性乳化沥青性能的影响,结果表明,采用100目胶粉即可制备出橡胶改性乳化沥青,但乳化沥青的性能较差;采用活化度为50%左右的100目脱硫胶粉制备乳化沥青时,脱硫胶粉的用量相比于胶粉可大幅提高;在通过外掺100目50%左右活化度的脱硫胶粉(质量分数15%,以沥青计,下同)和质量分数2%的苯乙烯-丁二烯-苯乙烯嵌段共聚物改性的乳化沥青中添加质量分数1%的丁苯胶乳,所制备橡胶改性乳化沥青无筛上剩余物,5 d储存稳定性为2.9%,蒸发残留物的25℃针入度、软化点和5℃延度分别为55 (0.1 mm)、64.5℃和22.5 cm,能够满足乳化改性沥青的技术指标要求。     

于都县黄麟地区绿色富硒土壤分布选区评价

通过于都县黄麟地区1:5万土地质量地球化学调查,基本査明该地区农作物中硒元素及其他元素的地球化学特征,综合分析岀绿色富硒土壤分布,并优选出绿色富硒地块,为特色农产品基地建设的开发与利用提供理论依据。     

A unified critical state model for geomaterials with an application to tunnelling

This paper is prepared in honour of Professor E.T. Brown for his outstanding contributions to rock mechanics and geotechnical engineering and also for his personal influence on the first author's research career in geomechanics and geotechnical engineering. As a result, we have picked a topic that reflects two key research areas in which Professor E.T. Brown has made seminal contributions over a long and distinguished career. These two areas are concerned with the application of the critical state concept to modelling geomaterials and the analysis of underground excavation or tunnelling in geomaterials.Partially due to Professor Brown's influence, the first author has also been conducting research in these two areas over many years. In particular, this paper aims to describe briefly the development of a unified critical state model for geomaterials together with an application to cavity contraction problems and tunnelling in soils.     

Seismic behavior of geosynthetic-reinforced retaining walls backfilled with cohesive soil

This study investigates the seismic performance of geosynthetic-reinforced modular block retaining walls backfilled with cohesive, fine grained clay-sand soil mixture. Shaking table tests were performed for three ½ scaled (wall height 190 cm) and ¼ scaled model walls to investigate the effects of backfill type, the influence of reinforcement length and reinforcement stiffness effects. The El Centro and Kobe earthquake records of varying amplitudes were used as base acceleration. Displacement of the front wall, accelerations at different locations, strains on the reinforcements, and the visual observations of the facing and the backfill surface were used to evaluate the seismic performance of model walls. The model walls were subjected to rigorous shaking and the walls did not exhibit any stability problems or signs of impending failure. The maximum deformations observed on the models with cohesive backfill was less than half of the deformation of the sand model. The load transfers between the geogrid and cohesive soil was comparable to that of sand and hence the needed reinforcement length was similar as well. As a result; the model walls with cohesive backfills performed within acceptable limits under seismic loading conditions when compared with granular backfilled counterparts.     

餐厨污水就地处理与中水回用工艺的探索与实践

以无锡某厂食堂污水处理及中水回用为例,探讨采用"隔油+混凝沉淀+A^2/O+MBR"工艺就地处理餐厨污水,并将出水回用于厂区冲厕可行性。经过78 d的调试,该工艺实现了餐厨污水中污染物的去除,COD小于50mg/L,NH4^+-N质量浓度小于5 mg/L,总氮小于10 mg/L,总磷小于0.5 mg/L,大肠杆菌数小于2个/L,基本满足中水回用要求。经计算吨水处理成本9.83元,含电费、药剂费、人工费、污泥处理费及膜更换费用。结合中水回用节省自来水后计算吨水处理综合成本为5.23元,大幅降低公司对市政供水的依赖,降低公司用水成本。     

Critical state model for structured soil

Structure is an evident determinant for macroscopic behaviors of soils. However, this is not taken into account in most constitutive models, as structure is a rather complex issue in models. For this, it is important to develop and implement simple models that can reflect this important aspect of soil behavior. This paper tried to model structured soils based on well-established concepts, such as critical state and sub-loading. Critical state is the core of the classic Cam Clay model. The sub-loading concept implies adoption of an inner (sub-loading) yield surface, according to specific hardening rules for some internal strain-like state variables. Nakai and co-workers proposed such internal variables for controlling density (ρ) and structure (ω), using a modified stress space, called t_ij. Herein, similar variables are used in the context of the better-known invariants (p and q) of the Cam Clay model. This change requires explicit adoption of a non-associated flow rule for the sub-loading surface. This is accomplished by modifying the dilatancy ratio of the Cam Clay model, as a function of the new internal variables. These modifications are described and implemented under three-dimensional (3D) conditions. The model is then applied to simulating laboratory tests under different stress paths and the results are compared to experiments reported for different types of structured soils. The good agreements show the capacity and potential of the proposed model.